Help with slightly botched Rev200 conv

[goin on 4T]

You are not going to get tren ace to hold at 200mg/ml in gso.
You need to go to the grocery store and buy a bottle of gso.
Don't add anymore ba or bb.
16g = 160ml @ 100mg/ml
You have too much ba and bb if you do 100mg/ml but it won't kill you.
So what do you want?
100mg/ml
Or 80mg/ml?

 

[1stateofmind]

100mg/ml. I'll have to get some more gso(which I'm assuming is grape seed oil). Is it okay to mix what I have(I'll try to attach a pic) with the oil?

 

[goin on 4T]

Why did you put it in a sealed vial?
You do know that you have to filter it?
It's not sterile until after its filtered.

 

[1stateofmind]

It's not sealed. It has a rubber cap on if. Does the mixture look even close to how it's supposed to be? This is 16g powder and 16ml(4ml ba 12ml bb).

 

[goin on 4T]

Well because you did not heat it, yes it looks like a bunch of stuff put in solvents that were not heated.

 

[1stateofmind]

Never saw where I needed to heat it until I heard it from you. How would you recommend I heat it and for how long? And what is it supposed to look like afterwards? Thanks for your insight by the way, it's greatly appreciated.

 

[goin on 4T]

Now I can the pic better on my pc screen than on phone. What that looks like shit! LOL
Don't worry I have made some ugly shit before too.
Get a litre of Grape seed oil at the grocery store.
Get a large frying pan add 1-2 inches of water. Set it on low heat.
Pour as much of that stuff into beaker as you can, then put both in the boiling water to heat them slowly.
Do not let the water in the pan get to a full boil, you may need to add water to the pan never let it go dry.
Once the vial holding that crap is warm try and pour all into the beaker.
When the temp in the beaker gets between 110-130 the solution should become clear and the crap suspended in the solvents (BA and BB)
Let it stay warm for 20 min 120 -140 degree F.
Then add 130 ml of the GS oil to the beaker. Again heat to 120-140 F.
That should give you 160ml of 100mg/ml.
Then you will need to filter your solution.
What type of filter are you using?

 

[1stateofmind]

Whataman .45. I think I said the name right

 

[goin on 4T]

.45 isn't good enough bro. You need to use .2 what man

 

[UA_Iron]

you will be sorely disappointed with 200mg/ml test propionate from this conversion.

One should always use .22um or finer filters for filtration - .45um will not filter out a magnitude of common viruses. .22um will get out 99% of everything - with the exception of rare prions that typically do not exist in ones homebrewing environment.

Your filter element should be composed of PVDF or PTFE as these are both compatible with BA and BB at the prescribed percent compositions. Other membrane elements are not compatible and can erode or react negatively to the BA/BB. PTFE is the best for material compatibility, but it has a tendency to clog faster than PVDF due to unequal distribution of pore size (my own personal theory).

Your solution appears that is has not yet gone into solution - your final composition for test prop 100mg/ml with 16g of raw powder should be:

4ml BA (since you have BA at 2.5%, this is acceptable I suppose)
32ml BB (should be at 20% with prop)
109.46ml Carrier oil (preferably GSO as goin on 4T mentioned)
16g Test prop powder

for a total of 160ml @ 100mg/ml.