Kronk had posted this about a month ago. I think this should work out for you. He seems to really know alot about injections and any thing else that has to do with it.INJECTION TIPS
Ok. So you need to make sure that you have your needles and syringes. You will want to get around a 22 gauge with a 1 1/2 inch needle. I suggest you get a 5cc syringe as it gives you more to hold on to when injecting. Make sure you have enough of these for all your injections BEFORE you start. Don’t run out and not be able to take your inject.
Here is how you should inject.
First off, you will want to inject into the upper corner of your glute. Imagine a line running up and down on your ass crack, and then draw another line across the middle of your butt. Aim for the upper corner on either side of you ass. You will need to prep the area with some rubbing alcohol as well. Make sure everything is very clean. Here is a breakdown:
1. Draw your gear in the syringe with a new needle.
2. Replace the needle with a fresh one prior to inject.
3. Squeeze out the air bubbles
4. Clean the injection site with rubbing alcohol.
5. Slowly stick the needle inside of your glute.
6. Aspirate (pull the plunger back to see if any blood comes back, if so you hit a vein. Remove needle and start over) If no blood you didn't hit a vein, and keep going.
7. Squeeze the syringe very slowly. Take your time to inject, the slower you go, the less pain there will be. Pull the needle out when done.
8. Clean off area again with alcohol.
To deal with some more painful gear, now is a good time for a light massage and if possible, stick your butt on a heating pad for about 10 mins. This will help with the pain. You can also run your syringe under hot tap water for about 60 seconds (with the gear in it) before you inject. This makes the oil easier to inject and disperse when it is inside you. I have also included some other ways to lessen the pain. Please see below:
Most of the pain you goes in certain AS (Ttokkyo/IP etc.)is due to the high BA (benzyl alcohol) content. Hopefully one of these will help allot of you bro's out.
1. Try mixing the painful to inject steroid with one that is not painful to inject. Such as Ttokkyo's Sust mixed with Deca. Or Prop with EQ. There are many combos but you get the idea. This somewhat dilutes the overall BA content. Its like not being able to drink vodka straight, but mix it with some orange juice and you can drink tons of it without any problems. This is nothing new; most of you already know this.
2. Try applying a heat pad over the injection area for 10 min directly after you inject. A light massage during this time will help as well. Some guys like to rub on some icy hot at this point, I do this and it really works.
3. Try baking your vials to reduce BA levels. Here is how you do it. Preheat your oven to 250 degrees. Place a cookie sheet in the middle rack. Take a small gauge needle such as 25g and stick it in the vial. Do not put the tip of the needle into the oil; leave it just above the oil. Stand the vial up in the middle of the cookie sheet and let it bake for 15 minutes. Take it out let it cool and repeat this once more. While it’s baking the BA will vaporize and exit via the needle. This will greatly reduce the BA content and should result in a less painful shot. You might loss an ml after it’s all done but not much.
4. Try using sterile water to take the BA out. Buy some sterile water, bacteriostatic
water. You also need a 5ml syringe. The day before your shot mix 1ml of the painful steroid with 2ml of the water in the 5ml syringe. Pull back the plunger and shake hard for one minute. Let it sit overnight with the cap on the needle of course. Right before your ready to shoot it point the needle down, the BA will be mixed with the water and then you just shoot out the BA/water mix. You will have pure oil/steroid left. Do this all at a cool room temp, heat and steroids without any BA don’t mix. What will be left will be a thick oil so use the proper gauge needle such as 23.
If none of the above work, or a mixture of several of the above doesn’t work then send me your gear for free disposal! I will be happy to take it off your hands, DONT THROW IT AWAY!
Please Scroll Down to See Forums Below 
, the actual little prick ain't shit.... just my 2 cents
