Please Scroll Down to See Forums Below
how many fina carts for 6 week cycle
- Thread starter jstanziale
- Start date
Wait a minute, isn't the "magic solvent" BA? Why add BA? And I thought you were supposed to leave the pellets crushed up in the solution for at least one hour or until the pellets are completely dissolved? The add the oil, shake vigorously, let sit for the night, pull the product, filter the product (filter again if you like) and bake at 170-190 degrees for one half to one hour...
freakazoid
New member
ok i am gona get flamed for this but i have never bought a kit,and never had an abcess,and have done this alot.so if anyone does this,do it at your own risk. first off crush 4 pellets as fine as you can get them.crush them on a thick piece of paper.put a 21 ga. needle on the end of your syringe(so that your fina wont fall out) pull the plunger out of the syringe.take the paper with the fina on it and bend it so that the fina will fall into the syringe.put the plunger back on,hold the syringe with the needle up and push all the air out.then put the needle in the oil (wesson is what i use) draw 1cc of oil out,then fill the rest of the syringe with air.put the cap back on the needle and shake vigerously.take a small pot and fill it with water,heat it to 250 degrees,put the syringe in the pot with the needle up(so no oil leaks out)heat it for 10 min.heat it 2 times for a total of 20 min while shakeing it every few minutes.now let it cool to room temp with the needle pointing up.you will notice all the fillers will settle to the bottom.right before you shoot shake it up and then let all the air out of the syringe then inject,fillers and all.(note)you will have to use at least a 21ga or it will clog.you can add some benz alcohol if you like. now you think i am crazy,but i actually did a little research on this and years ago dan duchaine stated he used to use a coffee grinder and did it this way.that was before he came up with the new method witch is now the "kit". your body will metabolise the "fillers"and imo its as safe as injecting some "magic solution"that people sell in there kits,that no one knows what the hell it is.so i have done it for several cycles like this with no complications whatsoever,but that doesnt mean i wont.so i dont want some newbie trying somthing like this and his ass rot off,im just telling you this is how i do itcbr1100xx said:
freakazoid
New member
actually oak it is painless,besides the pin prick.i guess because i use no b.a.but i see your point,just the thought of it i guess would detour most from trying it.but i did not just come up with this idea,as i stated before this method was used years ago after they took tren off the market.OAKBOX said:
Jc21, I've only bought one kit and it only came with one "magic solution" vial, not two. So I’m not sure what you mean by the BA is what you add second... I followed these rules of preparation:
http://www.gotfina.com/articles/make.html
BTW, heating has to be safe at very low temperatures. I've heard, to brake the chemical bond between the tren and BA, you'd have to heat the solution to 900 degrees- could be an exaggeration, but 180 is not going to hurt your gear, it'll just kill the animals in it...
http://www.gotfina.com/articles/make.html
BTW, heating has to be safe at very low temperatures. I've heard, to brake the chemical bond between the tren and BA, you'd have to heat the solution to 900 degrees- could be an exaggeration, but 180 is not going to hurt your gear, it'll just kill the animals in it...
jc21
New member
i think i was on crack the first time i wrote it.
nope the majic solvent is to dissolve the binders and fillers, the BA is what you add second. I dont do all that heating and waiting crap. Dont let anyone tell you to heat it when they have no idea at what temperature the compounds denature at.
where did these people look up the melting point for tren....in the crc i dont think so. i have made tons and never heated it, nobody has ever gotten an infection.
