tren w insulin pin?

[ryno9000]

I don't understand how if you can't draw it up, you can push it out??

 

[Cardinal Slin]

I don't understand how if you can't draw it up, you can push it out??

I would imagine with pushin you can put more pressure on it than pulling but in any case I have drawn masteron, tren, winny, primo and sustanon in to a slin pin and all took less than a minute to fill a 1ml syringe - the hardest was the sustanon...

 

[Acela]

If you are going to try a slin pin then I would heat the loaded syringe (personally, i put it on a piece of paper and let it sit, monitered, on my space heater....it's a fireproof one.....not the old school space heaters that you may be thinking of)

heating the oil will make it push thru easier

 

[HAYEZ]

I don't understand how if you can't draw it up, you can push it out??

u dont draw with the pin,.,you remove the plunger and fill the barrel..replace the plunger and shoot

 

[ryno9000]

u dont draw with the pin,.,you remove the plunger and fill the barrel..replace the plunger and shoot

No I fully understand backloading. I'm just saying it seems weird that if something is too thick to pull up, how can you push the same liquid out? It goes through the same hole either direction, so its just weird to me. Its like trying to get a couch through a door. If you can't pull it in, why would you be able to push it out? But I trust you, I'll just have to try it some time.

 

[rakasha681]

No I fully understand backloading. I'm just saying it seems weird that if something is too thick to pull up, how can you push the same liquid out? It goes through the same hole either direction, so its just weird to me. Its like trying to get a couch through a door. If you can't pull it in, why would you be able to push it out? But I trust you, I'll just have to try it some time.

Its just some fun physics. Basically, when you try to draw, the only thing making the draw happen is the back-pressure created from the vacuum of pulling the plunger up, which isnt a whole lot of pressure/force. When you push on the plunger with your thumb, all the force from your muscles pushing the plunger is exerted.

So its not that it can go one way through the needle and not the other, its more that there is a lot more pressure exerted the other way.


For those wondering if the 1/2" pin is deep enough, it mostly is depending on where your shooting, my fat ass is not a good canidate, but just about everywhere else is fine. If your worried about it, instead of using the one piece slin pins, you can use your standard barrels and get 3/4 and 1" length pins. 30x1 are hard as hell to find, i have a few, but i wouldnt really recomend them, the length adds flexibility to the needle, and thats not good. If you can find 29x.75, they are great, but i havent been able to find any in a few years, jusing using the 30x.5 for everywhere cept glutes, use the good 'ol 25.

 

[Jarebear]

I shoot TA ED in my pecs and delts and just started in my quads(hurt like hell), as long as your body fat is low enough in the injection site you have no problem

 

[rustilldown]

I've drawn tren and masteron into a slin pin and had great results injecting into "quads, delts, triceps, pecs" I just pull the plunger , prop the needle up on something pull the plunger halfway back and then let the back pressure and gravity do the work. Takes about a minute or 2 to fully load 1 ml but the pins are easy to do day after day and yes it works

 

[Race121]

This most definitely works. I ran Tren A this way (ED) last spring and it worked great. Just be sure and aspirate. I've done hundreds of shots over the years and have aspirated blood twice. Both times were Tren shots to the triceps.