test e 400mg/ml

[pov]

hello bros, im new to homebrew been doing some research and think ill be ready to make my own gear soon.

i looked at many recipes of T.E and most of them are 250mg/ml. just wondering why is this, is there any specific to why a higher dose isnt posted?

 

[needtogetaas]

There is recipe for higher dosing. But high dose is painful.

 

[pov]

There is recipe for higher dosing. But high dose is painful.

lol you the man, its like you stalk me and your always the 1st to help, thanks bro

ive looked everywhere i cannot find it. ill try looking agian lol

would T.E400 hurt if i mixed it with deca 100mg/ml?

im planning for a future cycle of
T.E 800mg
deca 600mg

 

[wee_man]

Painless T-400

Items Needed for a 20 gram conversion:
10 grams Testosterone Enanthate & 10 grams Testosterone Cypionate
1.0ml benzyl alcohol (2% BA)
10.0ml benzyl benzoate (20% BB)
12.0ml oil
12.0ml Ethyl Oleate
Syringes 3cc & 5cc or 10cc
20 gauge needles
Mixing vial (or preferably beaker)
Sterile vial
Sterile syringe filter
Weigh out 10 grams of hormone into mixing vial or beaker.
Add benzyl alcohol , benzyl benzoate and 19.0cc of oil/EO mix. (This will leave 5cc oil/EO for later.)
Place on stovetop (electric stove) or frying pan (gas stove) on medium high heat.
Swirl and heat until soultion is completely homogeneous and clear. NO hormone "swirls" , crystals, or visible separation should be left.
Place 20g needle in sterile vial and attach syringe filter.
Place another needle through stopper to releave pressure
Draw out hormone solution with 5 or 10cc syringe and run it through the syringe filter until all solution is filtered.
Run the addition 5cc of saved oil from step 2 through syringe filter to purge.
This conversion results in 50ml - 400mg/ml sterile solution for injection.

 

[nydj66]

Painless T-400

Items Needed for a 20 gram conversion:
10 grams Testosterone Enanthate & 10 grams Testosterone Cypionate
1.0ml benzyl alcohol (2% BA)
10.0ml benzyl benzoate (20% BB)
12.0ml oil
12.0ml Ethyl Oleate
Syringes 3cc & 5cc or 10cc
20 gauge needles
Mixing vial (or preferably beaker)
Sterile vial
Sterile syringe filter
Weigh out 10 grams of hormone into mixing vial or beaker.
Add benzyl alcohol , benzyl benzoate and 19.0cc of oil/EO mix. (This will leave 5cc oil/EO for later.)
Place on stovetop (electric stove) or frying pan (gas stove) on medium high heat.
Swirl and heat until soultion is completely homogeneous and clear. NO hormone "swirls" , crystals, or visible separation should be left.
Place 20g needle in sterile vial and attach syringe filter.
Place another needle through stopper to releave pressure
Draw out hormone solution with 5 or 10cc syringe and run it through the syringe filter until all solution is filtered.
Run the addition 5cc of saved oil from step 2 through syringe filter to purge.
This conversion results in 50ml - 400mg/ml sterile solution for injection.

Test enanthate is supposedly oil soluble at room temperature and requires only 3% BA to keep it sterile (for 250mg/ml). So I'm suprised you need 20% BB to get to 400mg/ml when using EO.

 

[Ste-Rhino]

why not just do it at 200mg/ml and use only 1% BA, It saves spending the extra money on other chems and is simple as enanthate can be done with your eyes closed.

10g powder

40ml oil

0.5ml BA

Heat oil&ba in a glass pan add powder stir with glass rod until desolved.. Filter.. leave for 2-3 days.. Inject.. Done.

Rhino.

 

[nydj66]

why not just do it at 200mg/ml and use only 1% BA, It saves spending the extra money on other chems and is simple as enanthate can be done with your eyes closed.

10g powder

40ml oil

0.5ml BA

Heat oil&ba in a glass pan add powder stir with glass rod until desolved.. Filter.. leave for 2-3 days.. Inject.. Done.

Rhino.

I like to use 3% BA to ensure sterility. Even at 3% there is no injection pain.

 

[wee_man]

Test enanthate is supposedly oil soluble at room temperature and requires only 3% BA to keep it sterile (for 250mg/ml). So I'm suprised you need 20% BB to get to 400mg/ml when using EO.

Because I posted a mixture of Testosterone Enanthate and Testosterone Cypionate. The BB not only helps dissolve the cypionate, but it funtions as a preservative and thins the solution. The EO, is for the pain, almost all compounds made a 400mg/hurt. The EO lessens the pain.

 

[bremac]

Because I posted a mixture of Testosterone Enanthate and Testosterone Cypionate. The BB not only helps dissolve the cypionate, but it funtions as a preservative and thins the solution. The EO, is for the pain, almost all compounds made a 400mg/hurt. The EO lessens the pain.

he's right the BB and EO are for the pain as they dissolve the steroid more effectively. BA does not hurt, it is a freezing agent in old medicine. 3% BA will even keep dog shit sterile and is all that is needed if you keep your concentrations in check, 400mgml is out of the ball park, that will crash in the depot 90% of the time. Lots of heat and massage no matter how much EO you use.
3-5% BA in sesame or grapeseed don't exceed 75mgml for prop or 125mgml for enan or cyp=no pain ever.