Help with grey looking tren conversion

[1stateofmind]

Hoping someone can give me some insight on getting a revalor 200 conversion back on track. Done this conversion before(using basskiller a step by step) and it worked perfectly. The only difference now is that for the estro solubilizer I couldn't find due to my source site being gone so I had to make my own using sodium hydroxide(100% lye crystals). I did my research on this and found a ratio of 1 gram of lye dissolved in 20ml of distilled water for every 2g cart of revalor I used. I did two batches at the same time using 6 carts in each so that's 6grams of lye(which sounded like a lot but lye is super heavy so it was barely a tablespoon maybe) in 120ml distilled water. When I added the lye solution to my methanol(heet) revalor solution it immediately turned white which I expected due to the large amount of water added and it looked okay. I let it sit for an hour and when I came back it had turned green, like almost opaque dark pea green. I then slowly added my distilled water using the drip method to try to get crystallization. I then ran everything through a filter and was left with a grayish green powder instead of white how it's supposed to look. I'd love to think that I could just add this to my bb/ba solution and run with it but wanted to check with the forum to make sure I don't need to start over and dissolve it back in heet and try again. I tried rinsing and rinsing and cloudy gray water is what came out the other end but it's still grey. Please help!!!!

 

[1stateofmind]

Tried a small amount in bb/ba and now it looks dark grey and kinda slimy even after heated. Looks like I may have to start over which really sucks. Any experiences with botched conversions like this would be greatly appreciated.

 

[Mh48500]

Doesnt sound good bro. I only ever converted Fina so never had to deal with the estro solubilizer. Hopefully someone one chimes in or maybe post it in the chem section, Basskiller himself has posted recently and might be able to help you best.

Good luck.

 

[basskiller]

you can not use red devil lye because it contains things other than sodium hydroxide (NaOH) 125 to 150mgs will suffice

 

[1stateofmind]

Definitely didn't use red devil. Used 100% lye crystals. Tried putting the dried gray powder back in heet but now I'm left with some heet solution that looks like brackish water. Starting to feel like its a lost cause. Any ideas or am I screwed?

 

[1stateofmind]

I'm thinking about trying the slow water drip to re crystallize and get it back to powder. Im almost positive I'll end up with grayish looking powder again. I'm questioning whether this will be useable. There shouldn't be any lye residuals left due to rinsing but am I being an idiot for trying to use this? I'm just hesitant about throwing out 20g of tren powder.

 

[johnjosephholly]

Mine turned out grey, what did you do?

 

[RagingBlizzard]

Mine also turned green, I dissolved the lye pellets in water. A soon as I added the lye solution to the Revalor and Heet the Revalor/Heet immediately went from a yellow to a dark orange and a minute later it turned green. The bottom is a light pea green color and the top is either a VERY VERY dark Green or black.

I was afraid that if I dissolve the lye pellets in water that once I added the lye/water solution to the revalor/Heet that the tren ace and estradiol would immediately begin to crystallize because pure lye is no longer sold as a solution one has to dissolve the lye.

1stateofmind and johnjosephholly did you guys end up using the crystals anyway and injecting them? If you did; was the gear legit? Did it work 100% properly?

In 20 minutes I will begin the cold water drip, I have a feeling that I will not see any crystals or any crystallization.

I'm looking at the solution and I see a lot of fine particles of powder floating in the green liquid.