GEORGE SPELLWIN'S ANNOUNCEMENTS
Enlightening Men about Anabolic Steroids and Bodybuilding for over Two Decades
|
 Elite Fitness Bodybuilding, Anabolics, Diet, Life Extension, Wellness, Supplements, and Training Boards
 Anabolic Discussion Board
 fina, not dissolving
|
| Author | Topic: fina, not dissolving | ||
|
Amateur Bodybuilder 
Posts: 140 |
I crushed the pellets and added them an hour ago and they don't look like they've changed at all. How long do I let it sit? I am making with the Synthol Direct kit.     | ||
|
Cool Novice 
Posts: 13 |
I've never used the synthol kit, but I have used two oil kits. I assume you are using some sort of dissolving agent at this point. If so, I think I let it sit over night. You can also heat it up on low on your stove if it still isn't dissolved. Hope that helps. | ||
|
Amateur Bodybuilder
Posts: 140 |
Is that right? Anyone else? | ||
|
Elite Bodybuilder 
Posts: 1055 |
I just made one with the synthol direct kit, and I must say I like An#@#@s much better. I couldnt get my final solution as clear as I could with the formentioned's kits. | ||
|
Amateur Bodybuilder
Posts: 140 |
bump | ||
|
Amateur Bodybuilder
Posts: 102 |
Hey bro, I just made some fina with the Synthol kit. I crushed the pellets and let them sit for a couple of days (this means I had to prefilter) and heated in hot water now and then. The stuff separated with the oil on top and the darker brown fina in the bottom. I have ended up with a separated mixture, which I have heard a lot of people have done with their Synthol kits. When I shake it it turns a murky orange in color, but I have heard you can go ahead and use it like that as long as you shake it. Next time I'll get As kit. | ||
|
Amateur Bodybuilder
Posts: 140 |
my shir has been sitting for about 24 hours now, and it still aint done! WTF is goin on here? I suppose i have to heat it and wait now. So much for skipping the prefiltering. FUCK!!!!!! | ||
|
Moderator 
Posts: 1422 |
i let mine sit for 48 and i crushed them up a bit, seemed to workout just fine ------------------ | ||
|
Amateur Bodybuilder
Posts: 140 |
is it absolutely necessary that I prefilter, if I let it sit for 48 hours? | ||
|
Amateur Bodybuilder
Posts: 135 |
My last kit from Synthol took forever to breakdown. Heating is OK but not too hot. I never had to pre-filter because I heated before filtering with the sterile filter. | ||
|
Elite Bodybuilder
Posts: 624 |
i just made a some last night, but in the last step....my fina is still at the bottom and there is oil at the top, i guess this is how it is suppose to like? all you half to to is shake it first | ||
|
Amateur Bodybuilder
Posts: 140 |
I got some premade from a buddy one time and it was a yellow colored thickness at the bottom too. I just shook it up and heated it in almost boiling water. I worked pretty good but the end of the pin would get clogged, and ud have to purge it through when filling the syringe. Back and fourth , ya know. Took forever. I'm gonna give it a total of 48 hours to sit. Do I absolutely have to prefilter. Will I lose alot If o dont prefilter and squeese the clump at the end? | ||
|
Amateur Bodybuilder
Posts: 135 |
I use the same kit and never pre-filter. Synthol's secret solution doesn't turn to glue. Warm it after you add the oil and then warm it when you are going to use the sterile filter. Be patient the filter is a bitch. | ||
|
Amateur Bodybuilder
Posts: 140 |
cool thankx gunsg. do u waste alot left in the chunk at the bottom? |
All times are ET (US) | |
 |
|
|
posted December 27, 2000 06:44 PM