GEORGE SPELLWIN'S ANNOUNCEMENTS
Enlightening Men about Anabolic Steroids and Bodybuilding for over Two Decades
|
 Elite Fitness Bodybuilding, Anabolics, Diet, Life Extension, Wellness, Supplements, and Training Boards
 Anabolic Discussion Board
 25 gauge 1 inch ok for deca inject?
|
| Author | Topic: 25 gauge 1 inch ok for deca inject? | ||
|
Cool Novice 
Posts: 37 |
25 gauge 1 inch ok for deca inject?     | ||
|
Elite Bodybuilder 
Posts: 932 |
Yes. Quads and delts. Use 1.5" for your glutes. Some use 1" though. | ||
|
Elite Bodybuilder
Posts: 779 |
Depends... Best to stay with 1.5 in glute and quad and 1 in delt | ||
|
Cool Novice
Posts: 37 |
I will be injectin in the glute- will this be ok or should I buy a longer mofo 1 1/2 | ||
|
Pro Bodybuilder 
Posts: 574 |
sure, but you are going to hve to push the plunger hard to get it through the needle. ------------------ | ||
|
Pro Bodybuilder
Posts: 494 |
Yeah, I was going to say the same thing. You are going to have to push hard as hell to get deca through a 25 guage pin. Deca is thick as hell. [This message has been edited by The Ghost (edited December 08, 2000).] | ||
|
Amateur Bodybuilder 
Posts: 128 |
If you heat it up first you should be able to get it through, just might take a while. 1 inch is ok for your glute depending on how many cc's your injecting and how high your body fat is (less fat=shorter pin) but 1.5 inch is preferable. | ||
|
Amateur Bodybuilder
Posts: 73 |
A 25# 1/12 is fine especially if someone gives the inject its hard to push it takes a little while but its better than having golf ball knots on your glutes.keep a 22gauge to draw your deca then change your pin when injecting. | ||
|
Pro Bodybuilder
Posts: 391 |
I only use 25g pins. I have used Sustanon 250, Primobolan Depot and Deca with no problems. I run the syringe under warm water prior to injections. This thins out the gear prior to injection.... Works for me ------------------ | ||
|
Cool Novice
Posts: 37 |
Thanks fellas | ||
|
Cool Novice
Posts: 28 |
Pitbull you use a 22g to draw with? I've done it myself and found it to be annoying but it gets the job done. As for shooting deca with a 25g it is going to take a while to inject. I use a 22g and it doesn't hurt a bit. Just my opinion | ||
|
Elite Bodybuilder
Posts: 1336 |
22g to draw and shoot, always 1.5inch. . .I only shoot quads and gluts though. To much of a puss to shoot my delts or tri's. ------------------ | ||
|
Cool Novice
Posts: 28 |
Kodiak you fag! Just kidding bro I'll put 22g 1 inch in my delt but usually just 5/8 25g in my delt. Suck it up we're supposed to be the sick bastards. haha | ||
|
Pro Bodybuilder
Posts: 362 |
fuck 25 guage pins. Use 20guage missiles like me, it'll make a man outta you. But u can forget about sittin down on anythin but a sponge cushion hahah | ||
|
Amateur Bodybuilder
Posts: 247 |
I used an 1 1/2" on my delt the other day, pushed it all the way in. Meant to go half way but I turned my head as I was injecting for a second and when I looked back I noticed I pushed the pin all the way in my delt. Still didn't feel anything but I never would have pushed it all the way in on purpose. | ||
|
Cool Novice
Posts: 17 |
Remeber that your using an oil-based AS. With a water based you can get away with the 25. If your drawing with 25 you will have major problems too, in terms of time and patients. 22 guage will not hurt. You want pain, use one of the ice picks that come with sust.redijects, ooowwweeee!! 22.5s are okay too. Generally, 1.5 length for glutes to get through the adipose or fatty tissue and into the muscle. 1 inch for thighs and shoulders which will cause less scarring and you have much less fat deposited there to get through as well. Happy hunting! BigC |
All times are ET (US) | |
 |
|
|
posted December 08, 2000 03:47 PM