GEORGE SPELLWIN'S ANNOUNCEMENTS
Enlightening Men about Anabolic Steroids and Bodybuilding for over Two Decades
|
 Elite Fitness Bodybuilding, Anabolics, Diet, Life Extension, Wellness, Supplements, and Training Boards
 Anabolic Discussion Board
 To All SUS Users I Need Some Help...
|
| Author | Topic: To All SUS Users I Need Some Help... | ||
|
Pro Bodybuilder 
Posts: 372 |
This afternoon was my first time using SUS. I am going 750mg for 4 weeks and 400mg Deca all the way through. So tonight was 2cc's of SUS and 1 cc Deca. Thursday will be 1cc SUS, 1cc Deca. WELL, I drew 1cc of Deca great, then I broke of the two amps of SUS. But when I pulled back on the plunger to try and get the SUS all I got was air... So I got another needle got the cc of SUS and got another pin and got the other cc. Then Put both cc's into the first needle with the Deca. Please tell me that I am an idiot and you have a tip or something. My pins are 23 1/2 gauge. PLEASE HELP ME!!! greenhouse     | ||
|
Moderator 
Posts: 505 |
You need to make sure that between amps that you pushout all the air in the syringe. Insert the pin into the sust and push the air out. When you try and draw out the sust, be patient and don't pull too hard on the plunger. The sust is thicher than deca so it will move slower. BPP | ||
|
Pro Bodybuilder
Posts: 372 |
Thanks BPP, The deal is I did try and get all the air out between amps. But the Deca started to come out with it. I guess Ill just have to figure this one out with time. Its really hard to explain. ------------------ | ||
|
Moderator
Posts: 1562 |
Turn the pin upside down, flick it several times with your finger, then push the air out....as for the sus, before you draw, place the unbroken amps in a coffee mug full og hot tap water for a few minutes...loosens the oil, and injects much easier bro!!! ------------------ Ranger | ||
|
Pro Bodybuilder
Posts: 412 |
If the tips previously mentioned dont fix things for you, you might have had a bad syringe seal, it happens from time to time. If it happens again and the above dont help try a new syringe!!! | ||
|
Cool Novice 
Posts: 26 |
Try putting the sus in a cup of hot water to thin out the oil. When you push out the air you might lose a few more drops, but it will make the drawing process much easier. | ||
|
Elite Bodybuilder 
Posts: 1067 |
i was just about to say that ------------------ | ||
|
Elite Bodybuilder
Posts: 722 |
Use an 18 gauge to draw. | ||
|
Pro Bodybuilder
Posts: 459 |
use a 22gauge pin...pull real slow. got to be patient. out. ------------------ | ||
|
Pro Bodybuilder
Posts: 513 |
If you don't want to lose the few drops turn the pin upside down draw back a little more and then push the air out. Also like Bill said, soak the amps in warm water before you draw. | ||
|
Amateur Bodybuilder 
Posts: 273 |
Draw out with a 16-18g then switch to your 23gauge ( ps 1/2" deep with 3cc is gonna welt you up , so in a few days dont post " why do i have this big fucking lump " . The bigger the bolus , the deeper the injection ) Ps, make sure your points are on tight . | ||
|
Moderator
Posts: 336 |
If your impateint like myself, just get a lower gauge needle. Using a 23 to draw T200 was the most hellish ordeal I've ever been through. | ||
|
Cool Novice
Posts: 16 |
If this helps you can go to a feed store and grab one or to 16-18 g pins. When you just buy one or two they don't say anything. I think it might depend on what state your in too. |
All times are ET (US) | |
 |
|
|
posted August 21, 2000 10:21 PM