x
Almost there! Please complete this form and click the button below to gain instant access.
EliteFitness.com FREE Email Series: How You Can Use Winstrol, Masteron, HGH, and Testosterone for a Perfect, Muscular Physique!
- -
We hate SPAM and promise to keep your email address safe.
- -
  Elite Fitness Bodybuilding, Anabolics, Diet, Life Extension, Wellness, Supplements, and Training Boards
   Anabolic Discussion Board
  Test suspension how to

Post New Topic  
profile | register | preferences | faq | search

Author Topic:   Test suspension how to
Arnian

Amateur Bodybuilder

Posts: 56
From:
Registered: 2000

posted August 19, 2000 04:01 PM

Staff Use Only: IP: Logged


OK I'm sure a lot of you guy's have had this problem...I thought I was a know it all about juice but I had never used test suspension.....so I open a bottle, go to inject it, naddamn,I don't care if you can military press a Jeep, tht plunger won't move, it'll bend and break but the juice won't cokmeout (which i funny because BEFORE you stick it into the muscle.......)

The trick I've found is to mix equal parts B-12 and suspension, the suspension FIRST, then the B-12 (in the syringe) and it works fine......

Hope that helped someone because it was real tough for me to figure that one out!! LOL!!


Click Here to See the Profile for Arnian   Click Here to Email Arnian     Edit/Delete Message      Reply w/Quote
@LRG

Pro Bodybuilder

Posts: 316
From:
Registered: May 2000

posted August 19, 2000 04:14 PM

Staff Use Only: IP: Logged


sounds like a good trick, ill let my friend know cause hes tried about 20x with no luck.

im@LRG


Click Here to See the Profile for @LRG   Click Here to Email @LRG     Edit/Delete Message      Reply w/Quote
@LRG

Pro Bodybuilder

Posts: 316
From:
Registered: May 2000

posted August 19, 2000 04:16 PM

Staff Use Only: IP: Logged


sounds like a good trick, ill let my friend know cause hes tried about 20x with no luck.

im@LRG


Click Here to See the Profile for @LRG   Click Here to Email @LRG     Edit/Delete Message      Reply w/Quote
aahepp

Pro Bodybuilder

Posts: 441
From:Kentucky, US
Registered: May 2000

posted August 19, 2000 05:28 PM

Staff Use Only: IP: Logged


I mainly use suspension and haven't had that problem. I am taking this is a product that you purchased and didn't make and your home. My comes in powder form and I mix with some oil to inject. Even with it being thick oil I use a 27g. What I do is load the pin then let it sit in some hot water. After a few minutes the oil is easy to push thru. When I mixed it with water before I really never had any problems.


Click Here to See the Profile for aahepp   Click Here to Email aahepp     Edit/Delete Message    UIN: 82968675 Send a message to aahepp   Reply w/Quote
dynoalbino

Cool Novice

Posts: 22
From:
Registered: Aug 2000

posted August 19, 2000 05:33 PM

Staff Use Only: IP: Logged


previous post is on the money..heat some water in a pot..NOT BOILING...use tongs to dip in the water...peace


Click Here to See the Profile for dynoalbino   Click Here to Email dynoalbino     Edit/Delete Message      Reply w/Quote
Jae

Cool Novice

Posts: 24
From:Atlanta
Registered: Aug 2000

posted August 21, 2000 03:13 PM

Staff Use Only: IP: Logged


I've never had the problem either. One explaination is that Test Susp is a very irratating injectable. It burns, if you wipe the needle off with a sterile tissue when you pull out of the bottle, it removes the residue and that will not cause the muscle to irratate and swell, causing an airtight and inflammed injection point, which leads to the "No Mo Plunger Moving" episode. also, where did the needle break off? In your skin?

Jae


Click Here to See the Profile for Jae   Click Here to Email Jae     Edit/Delete Message      Reply w/Quote

All times are ET (US)

Post New Topic  
Hop to:

�2016 EliteFitness.com. All rights reserved.