GEORGE SPELLWIN'S ANNOUNCEMENTS
Enlightening Men about Anabolic Steroids and Bodybuilding for over Two Decades
 UBBFriend: Email This Page to Someone! |
 George Spellwin's ELITE FITNESS Discussion Boards
 Anabolic Discussion Board
 How to draw from amps?
|
| Author | Topic: How to draw from amps? |
|
Daeo Amateur Bodybuilder (Total posts: 48) |
posted August 14, 2000 10:50 PM
  
I have primo amps and I had a hard time pulling the liquid into the syringe today. It felt like the liquid was fighting to get back into the amp. Are there any tricks to make this easier? IP: Logged |
|
JUICESEEKER Pro Bodybuilder (Total posts: 403) |
posted August 14, 2000 10:53 PM
I WOULD SUGGEST WARMING IT IN WARM WATER, AND BREAK OPEN THE AMPS AND DUMP THE CONTENTS INTO THE SYRING AND DRAW UP THE CLUMPS AFTER. IP: Logged |
|
HackN2it Pro Bodybuilder (Total posts: 165) |
posted August 14, 2000 10:54 PM
What size darts are you using? ------------------ IP: Logged |
|
BigPapaPump Moderator (Total posts: 493) |
posted August 14, 2000 10:55 PM
Just be patient grasshopper ! If you can get larger pins, this will help draw the liquid faster. It does take time. BPP IP: Logged |
|
Daeo Amateur Bodybuilder (Total posts: 48) |
posted August 14, 2000 10:57 PM
I'm using 22 ga 1 1/2 needles. It just seemed like I was drawing 1cc for 5 freaking minutes. IP: Logged |
|
*B* Pro Bodybuilder (Total posts: 131) |
posted August 14, 2000 11:03 PM
Hey bro, try using a thicker guage pin to draw the gear and then just switch to a smaller pin to inject. I use a 18 ga. to draw and then switch to a 23 ga. to inject Omna.......... "B" IP: Logged |
|
lionheart Amateur Bodybuilder (Total posts: 73) |
posted August 14, 2000 11:14 PM
daeo, yea it does seem to take forever...... always warm up the amps and use a large size pin, not the one you inject with. If you use the same pin not only does it take a while to draw but you stand the risk of bending the tip of the point and tearing your ass up!!! CHECK OUT 2thicks web site he has LARGE size pins to draw with.......... If you order now you'll have them in time for your next shot his service is excellent. ENJOY IP: Logged |
|
BigTruck Pro Bodybuilder (Total posts: 268) |
posted August 15, 2000 10:42 AM
Yeah, my friend's got primo in his cycle and draws with an 18g and shoots with a 23g x 1.5 -- he says it works great! He ordered pins and barrels from 2Thick too -- 2Thick definitely comes through! Just e-mail him or visit the site. IP: Logged |
|
Jeff_rys Pro Bodybuilder (Total posts: 665) |
posted August 15, 2000 01:31 PM
i never draw Primo. You could do as i do remove the plunger and hold the open amp against the syringe and shake real hard using both hands. Open the amps you need first, then fill the syringe. Never had problems with that. it saves you a needle (i know they don't cost much). ------------------ Don't look back, life is too short IP: Logged |
|
bstrong Pro Bodybuilder (Total posts: 361) |
posted August 15, 2000 01:45 PM
ye if you'r having hard time do it Jeff's way, i used to do it when i was short of needels, it's a great way. JUST MAKE SURE THE PLUNGER DOSN'T TOUCH NOTHING, other wise u're gonna find how it is to an infection. IP: Logged |
|
THE APE Pro Bodybuilder (Total posts: 500) |
posted August 15, 2000 01:50 PM
Yeah,I do it the same way as jeff.Just move quickly and like the other bro says make sure to not let the plunger touch anything. IP: Logged |
|
Consultant Pro Bodybuilder (Total posts: 114) |
posted August 15, 2000 02:01 PM
1cc = five minutes something seems wrong. I have pulled up warm primo with a 23 all the time. Try heating the amps if you still have a prob I would get it tested! [This message has been edited by Consultant (edited August 15, 2000).] IP: Logged |
|
jersey boy Pro Bodybuilder (Total posts: 456) |
posted August 15, 2000 05:48 PM
Gotta use a bigger guage needle my friend.
IP: Logged |
All times are ET (US) | |
 |
|
|