GEORGE SPELLWIN'S ANNOUNCEMENTS
Enlightening Men about Anabolic Steroids and Bodybuilding for over Two Decades
 UBBFriend: Email This Page to Someone! |
 George Spellwin's ELITE FITNESS Discussion Boards
 Anabolic Discussion Board
 DRAWING GEAR W/AMPS
|
| Author | Topic: DRAWING GEAR W/AMPS |
|
rocky Pro Bodybuilder (Total posts: 317) |
posted June 28, 2000 02:28 PM
   I always hear of bro's drawing gear with a large guage needle, switching to a smaller pin, and injecting. The way I draw gear from amps is: It takes 2 seconds this way, and you don't need a drawing pin. Of course this will only work with amps. IP: Logged |
|
BigPappa Pro Bodybuilder (Total posts: 404) |
posted June 28, 2000 02:38 PM
Does ANY drip out when you turn amp upside down while the neck is off?...simply physics but just can't do because the thought of losing an amp is heart breaking. NO, I am not addicted, thank you. IP: Logged |
|
Vitaman Pro Bodybuilder (Total posts: 352) |
posted June 28, 2000 02:47 PM
I might this a try with an Amp I already used. I might put water into it to try this out first to make sure I can do it before I try the real thing. It does not look like a bad suggestion. ------------------ IP: Logged |
|
rocky Pro Bodybuilder (Total posts: 317) |
posted June 28, 2000 02:48 PM
No, I haven't had any drip out. I've done it with oils only though. To ensure that you won't spill any, you can slowly tip the amp until the liquid reaches the edge, have your syringe ready so your almost pouring it into the hole, and start drawing it out. It goes in very quickly. IP: Logged |
|
bollocks Pro Bodybuilder (Total posts: 144) |
posted June 28, 2000 03:52 PM
try this open amp take plunger out of pin, pour the stuff into the pin, no spill no prob. then put the plunger back in. easy!!! ps may need to flick the amp a bit to get all the stuff out. IP: Logged |
|
BigCatratcho Pro Bodybuilder (Total posts: 437) |
posted June 28, 2000 04:08 PM
just draw it out SLOWLY. needles are very skinny, so it takes a while, about one minute per cc ------------------ "tank tops are for medium sized guys..." IP: Logged |
|
rocky Pro Bodybuilder (Total posts: 317) |
posted June 28, 2000 04:11 PM
bollocks- yeah I've tried that too. Some of the oils are thick though, and I have a hard time getting it to pour out. IP: Logged |
|
Marauder Pro Bodybuilder (Total posts: 560) |
posted June 28, 2000 04:16 PM
be careful and don't spill any ultra! God that stuff stinks...and it feels like a crack rock on your tongue! nuuuuu-uuuumb! Marauder out. ------------------ IP: Logged |
|
mokhtarsayed Pro Bodybuilder (Total posts: 101) |
posted June 28, 2000 04:27 PM
I use the same way as Rocky. It seems like the easiest and nothing spills out. The problem I have when loading with the needle, is that you press it sometimes to the glass, and then the tip gets dull and really hurts when u inject. IP: Logged |
|
DYLAN Pro Bodybuilder (Total posts: 259) |
posted June 28, 2000 04:44 PM
That's why you should always change needles after you draw your juice. D. IP: Logged |
|
mokhtarsayed Pro Bodybuilder (Total posts: 101) |
posted June 28, 2000 04:51 PM
Or else use drawing needles like the ones 2thick has. IP: Logged |
|
bgriff Pro Bodybuilder (Total posts: 372) |
posted June 28, 2000 08:43 PM
hey bros dont you think that if you pour the oil in that any small pieces of glass that are in the amp will go in too!!! Man Ill bet that would hurt like hell to inject a peice of glass!!!! ------------------ IP: Logged |
All times are ET (US) | |
 |
|
|