GEORGE SPELLWIN'S ANNOUNCEMENTS
Enlightening Men about Anabolic Steroids and Bodybuilding for over Two Decades
 UBBFriend: Email This Page to Someone! |
 George Spellwin's ELITE FITNESS Discussion Boards
 Anabolic Discussion Board
 was I wasting gear using 1" pins?
|
| Author | Topic: was I wasting gear using 1" pins? |
|
code_x Pro Bodybuilder (Total posts: 127) |
posted June 28, 2000 01:44 PM
  
Today I switched from 23g 1" to 22g 1 1/2" pins just to be on the safe side. What happens if the gear doesn't get all of the way into the muscle? Is it still absorbed into the blood stream? My injection site is alternating glutes...-x IP: Logged |
|
Eramthgin Pro Bodybuilder (Total posts: 405) |
posted June 28, 2000 01:46 PM
Yes ------------------ If you enjoy it today you can always do it again tomorrow. IP: Logged |
|
code_x Pro Bodybuilder (Total posts: 127) |
posted June 28, 2000 01:48 PM
yes it gets absorbed or yes I was wasting it?-x IP: Logged |
|
Jim Layhoe Pro Bodybuilder (Total posts: 446) |
posted June 28, 2000 02:11 PM
they are fine if you don't have a huge fat ass.(23/1inch) I use them no-probs. IP: Logged |
|
naughty Pro Bodybuilder (Total posts: 240) |
posted June 28, 2000 02:15 PM
if the pin is too short it will be absorbed by the fat and be wasted... IP: Logged |
|
FLEXMEX Pro Bodybuilder (Total posts: 114) |
posted June 28, 2000 02:41 PM
try usin your quad instead of your glute..i think its alot easier. ------------------ IP: Logged |
|
lexicon Pro Bodybuilder (Total posts: 278) |
posted June 28, 2000 02:42 PM
If it was to go into fat instead of muscle the only problem (as far as absorption) would be that it would take more time to absorb. I cant see how it would be wasted. 1.5" are better, especially for glute shots. 1.0" will work but there is more of a chance of gear leaking out.Also, absorption may be slower with 1.0" due to slower absorption (Explained above) 1.0" is better for quads. Of course different sized/shaped people may warrent a change to these guidlines. IP: Logged |
|
Jeff_rys Pro Bodybuilder (Total posts: 310) |
posted June 28, 2000 03:08 PM
no, you should use a 23, 24 gauge and not bigger (for oil) and 1 inch should be fine. Just go a little higher on your butt. If I can shoot Winnie with a 1/2 inch in the glutt, then you certainly can use a 1 inch needle. But if you want to take a 1 1/2 inch and a 22 needle, well it is your choice? I will never use a 22 gauge ever again. Jeff ------------------ IP: Logged |
|
code_x Pro Bodybuilder (Total posts: 127) |
posted June 28, 2000 04:00 PM
Isn't there a site that shows how to do quad shots? I think I know how but, I'd like to be sure...I loaned out my Anabolic Reference Guide...do most of you guys do quad or glute shots?-x IP: Logged |
|
Will B.Huge Pro Bodybuilder (Total posts: 134) |
posted June 28, 2000 04:05 PM
Unles you are Rikishi the wrestler 1" pins are fine. Will IP: Logged |
|
JaySee Pro Bodybuilder (Total posts: 126) |
posted June 28, 2000 04:46 PM
Personally, I put Sustanon (or any other test) in my glutes. Everything else goes in quads or delts. IP: Logged |
|
micke Pro Bodybuilder (Total posts: 283) |
posted June 28, 2000 05:55 PM
bump... IP: Logged |
|
MattTheSkywalker Moderator (Total posts: 1109) |
posted June 28, 2000 06:24 PM
As a general rule, use 1.5". 1" will work if you don't have much fat but 1.5 is better just to be on the safe side. matt IP: Logged |
|
bgriff Pro Bodybuilder (Total posts: 413) |
posted June 28, 2000 08:26 PM
i use 1 1/2 inchers and stick it all of the way in!! ------------------ IP: Logged |
|
jersey boy Amateur Bodybuilder (Total posts: 98) |
posted June 29, 2000 11:30 AM
hit the delts and watch those cannon balls swell.
IP: Logged |
|
Motorhed Pro Bodybuilder (Total posts: 164) |
posted June 29, 2000 01:33 PM
good info. I am using 25/1" for quad shots of winny. got tired of 22/1.5" Thanx! IP: Logged |
All times are ET (US) | |
 |
|
|