GEORGE SPELLWIN'S ANNOUNCEMENTS
Enlightening Men about Anabolic Steroids and Bodybuilding for over Two Decades
 UBBFriend: Email This Page to Someone! |
 George Spellwin's ELITE FITNESS Discussion Boards
 Anabolic Discussion Board
 quick sust250 question...
|
| Author | Topic: quick sust250 question... |
|
devildogg Amateur Bodybuilder (Total posts: 36) |
posted June 08, 2000 12:11 AM
  
I got 10 1cc amps of sust250 today, the problem is I cannot figure out how to draw out the sust. I couldn't find any opening in the glass amp. Somebody please clue me in here. Thanks. IP: Logged |
|
Dutch Pro Bodybuilder (Total posts: 265) |
posted June 08, 2000 12:20 AM
Are you joking ??? If not you have to break of the top part of the ampul. use the cap of a big pen, place it over the top and snap it off quick. Dutch IP: Logged |
|
devildogg Amateur Bodybuilder (Total posts: 36) |
posted June 08, 2000 12:26 AM
no, I wasn't joking...but thanks for the help. IP: Logged |
|
Dutch Pro Bodybuilder (Total posts: 265) |
posted June 08, 2000 12:36 AM
Okee, make sure that there is no test left in the top of the ampul. Dutch IP: Logged |
|
TheBear Amateur Bodybuilder (Total posts: 82) |
posted June 08, 2000 11:53 AM
Use two pins as well cuz you will dull the first pin at the bottom of the amp IP: Logged |
|
TooJacked Amateur Bodybuilder (Total posts: 34) |
posted June 08, 2000 02:26 PM
you could also use a metal nail file, and saw around the amp. Then cover your fingers with a sock or something and just break it off, should come off easy after you file it IP: Logged |
|
GymRatSD Amateur Bodybuilder (Total posts: 7) |
posted June 08, 2000 02:28 PM
Be VERY careful with those ampules. If you can, get a syringe with a filter on it, otherwise you could be injecting small glass particles in your ass. Not a pleasant experience, let me tell you. IP: Logged |
|
devildogg Amateur Bodybuilder (Total posts: 36) |
posted June 08, 2000 02:40 PM
thanks for the help guys...I cracked the top off, but I am having trouble drawing out the sust because I can't flip it over and draw it out like the bottles. Is there any technique that I should be using? IP: Logged |
|
devildogg Amateur Bodybuilder (Total posts: 36) |
posted June 08, 2000 03:44 PM
I've tried to draw it out...its not working. I must be doing something wrong. Help. IP: Logged |
|
Buff Amateur Bodybuilder (Total posts: 7) |
posted June 08, 2000 03:56 PM
picture your sust amp as a glass of liquid and use the needle as a straw. tilt the amp slightly so it collect in one end of the amp...put the needle where it is collecting and draw out..hold the amp in one hand and the needle in the other, use thumb and index finger to pull up stopper on syringe..hope this helps IP: Logged |
|
rookiejuicer Pro Bodybuilder (Total posts: 128) |
posted June 08, 2000 04:43 PM
wow... now thats a newbie for you... wheeewwww.... hope everything works well for you buddy... IP: Logged |
|
RC Amateur Bodybuilder (Total posts: 22) |
posted June 08, 2000 04:51 PM
Dude send me your amps I'll open them for you hehe IP: Logged |
|
chemdaddy Amateur Bodybuilder (Total posts: 18) |
posted June 08, 2000 07:23 PM
after you open your amp, you can pour it into the back of the cylinder of your syringe (the needle is pointed down while doing this, obviously). Then gently put the plunger back into the cylinder just enough to seal the end. Then tip the needle up and press out the air. This works and spares you some needle dulling. It takes a little bit of time for it all to pour out, so be patient. I've never had glass in my oil, but if you did that might be a problem. If you break the ampule clean you should be fine, though. IP: Logged |
|
devildogg Amateur Bodybuilder (Total posts: 36) |
posted June 08, 2000 08:52 PM
thanx for the help guys...I'm really not that clueless, I just have never dealt with amps before. I'd rather ask you guys than screw it up doing it the wrong way. IP: Logged |
All times are ET (US) | |
 |
|
|