GEORGE SPELLWIN'S ANNOUNCEMENTS
Enlightening Men about Anabolic Steroids and Bodybuilding for over Two Decades
| Author | Topic: Making fina--question. | ||
|
Amateur Bodybuilder 
Posts: 281 |
After I added the pellets to the 'magic solution', i allowed the mixture to settle overnite. Well, today, after crushing and heating the pellets, they disolved, but there is a layer of white pellets on the bottom of the vial. is it ok to add the oil, or do i need to let them sit longer?    | ||
|
Amateur Bodybuilder
Posts: 281 |
bump | ||
|
Amateur Bodybuilder
Posts: 103 |
Man, I don't know if you're joking or not, but if you're serious, you probably need to start over. You are supposed to add the oil to the dissolving liquid/pellet combo within an hour. If you dont, oxidation can occur and you need to do the coffee filter step. No problem there, what may be a problem is you heated it without the protection of the oil. Tren has a rather low melting point out of oil and you have probably killed the hormone. I wouldn't mess with it now. Get another kit and cart of fina and get some detailed instructions before you mix up the batch. Don't sweat it, it's cheap.  | ||
|
Cool Novice 
Posts: 35 |
BigKraut is half right...you are supposed to add the oil w/i one hour. However, you aren't fucked, all is not lost, you'll just have to do some additional filtering and shit. Mosey your ass over to Mr. H's site https://www.elitefitness.com/members/finaplix/ and click on make fina, then click on detailed instructions w/ faq from animal...scroll down to sterile kit if you did get your kit from Mr A (if not ignore my entire post). I made the exact opposite mistake last night (my 1st time too) I put the oil in immediately after I put the pellets in the magic vial...today I've been spending a lot of time over the stove trying to get the shit to go into solution...its happening slowly but oh well...live and learn. | ||
|
Amateur Bodybuilder
Posts: 103 |
Bro, I got to disagree with you. I've made a load of the stuff and have studied it pretty throughly. If he hadn't heated it, you would be right. He would only need to take the additional filtering step, which is what I said. The main problem that I see is that he heated it without the protection of the oil. In oil, trens melting point is about 300 degrees F. Without oil, it is less than 200 degrees. So it sounds like he could have very well destroyed the active hormone. If that's the case it would be pointless to inject it. Harmless but pointless. | ||
|
Amateur Bodybuilder
Posts: 160 |
I dissagree kraut, You are told that you need to use heat sometimes to excell the breakdown process of the pellets in the magic solution, then apon the pelets breaking down within the hour you are to then add the oil!! however it is impotant when heating the solution to use boiling water as your heating source so that you don't burn the solution. | ||
|
Elite Bodybuilder 
Posts: 730 |
You can heat the bottle of dissolving pellots in a bowl under running hot tap water which is never at boiling temp. Did the comp t-h the other day. The filtered product was a cloudy yellow. Is this normal with the new formula. In the past I'd done only finaplix and the solute was clear amber yellow. | ||
|
Amateur Bodybuilder
Posts: 185 |
jeez, i hope it's not that picky... i'm going to read, read, read when I start up my batch! ------------------ | ||
|
Amateur Bodybuilder
Posts: 103 |
You're going to have to refer me to the set of instructions that state you may need to heat the pellets in the dissolving liquid before adding the oil. I've never seen them. The instructions I have, which can be accessed from this site, state very clearly that the heating takes place AFTER the oil has been added. The oil protects the tren from the potential damage of the heat. The instructions are clear on the point that the oil, dissolving liquid/pellet mixture are heated and while the heating is taking place, the solution is gently swirled to further aid the dissolving process. This step allows the pellets to completely dissolve and pulls the fillers and what have you to the bottom of the vial. You can check it out yourself. So if this fellow got the stuff too hot out of the oil, he could have destroyed the tren. With that as a possibility, why risk injecting a worthless solution. It would be more prudent to do it again and know all is well with the mixture. | ||
|
Amateur Bodybuilder
Posts: 281 |
When I heated the solution, I never went close to boiling point, just in hot water.. | ||
|
Amateur Bodybuilder
Posts: 281 |
i boiled it once (after I added the oil) and everything is ok now. Thanks guys! | ||
|
Amateur Bodybuilder
Posts: 103 |
Glad to have been of assistance. |
All times are ET (US) | |
 |
|
|
posted April 13, 2001 06:41 PM