GEORGE SPELLWIN'S ANNOUNCEMENTS
Enlightening Men about Anabolic Steroids and Bodybuilding for over Two Decades
|
 Elite Fitness Bodybuilding, Anabolics, Diet, Life Extension, Wellness, Supplements, and Training Boards
 Anabolic Discussion Board
 HOw far into your muscle do you guys injet?
|
| Author | Topic: HOw far into your muscle do you guys injet? | ||
|
Pro Bodybuilder 
Posts: 374 |
I jusrt put it in a inch and pump away, is this wrong?     | ||
|
Pro Bodybuilder
Posts: 439 |
I go 3/4 to 1 1/2 depending on where. I push in very slow. If the muscle twitches I back out and start again. I aerate, but I have never hit a vein. | ||
|
Amateur Bodybuilder 
Posts: 295 |
I bury it all the way in just to be safe....I use 1 1/2" and it will go in the delt all the way..... | ||
|
Amateur Bodybuilder
Posts: 222 |
In the glute. I bury it 1-1/2 inches until it dimples the skin. | ||
|
Novice 
Posts: 5 |
I use a 21g 1 1/2" for the glutes 25g 1" for quads, calves, delts, and bis... I always bury it and aspirate before slowly injecting...hardcore__1 | ||
|
Amateur Bodybuilder
Posts: 189 |
glutes at about 1 1/4 inch...for people who keep hitting their sciatic nerve: don't inject where your ass cheek dimples in...inject very UPPER OUTER portion of cheek | ||
|
Pro Bodybuilder
Posts: 374 |
what happens if you inject the stuff into the bone or to close to the skin or pass through the muscle with the needLe? Anyways I notice that when I inject ,if I push hard enough there is s hsrd place that I mudt piudh hsrd to get through. What is this? Not the FUCKIN BONE I HOPE????? | ||
|
Amateur Bodybuilder
Posts: 189 |
ur not going to inject into the bone..that would be like trying to inject into ur computer screen..its too deep for the needle length usually...it would hurt pretty bad i would suspect...if u think u r going to hit your bone then u are injecting in the WRONG place..u can't just inject anywhere if u wanna be safe about it....too close to the skin you will waste some gear it won't get absorbed well and bruise more...thru the muscle? its skin fat muscle then bone, most likely u will hit muscle. the hard place is probably scar tissue from previous injections..or u r just a hard ass | ||
|
Pro Bodybuilder
Posts: 374 |
I am talking about the effect of "dimpling" the skin with the needle. In other words I am talking about the effect of pushing the base of the needle against the skin once the actual needle itself has been fully inserted. As of late I have been experimienting with dimpling the needle to varying degrees because I all of a sudden got paranoid that my injection technique has not been 100 percent and that I have been wasting gear. If I put the needle all the way in my quad and then push against the skin with the rest of the syringe to "dimple" it, if I really push hard enough it seems I hit some hard thing that hurts (only a little pinch). Is this the fucking bone? (I said I have an inch needle, this is wrong, I have a 5/8th inch needle) | ||
|
Amateur Bodybuilder
Posts: 135 |
I think you are hitting a nerve. Are you injecting into the outer lateral quadrant in your thigh? | ||
|
Amateur Bodybuilder
Posts: 222 |
DCS - I can feel that "pinch" too. It is when the needle enters the muscle from the fatty tissue. What is your %bf. If you feel that then you are OK. | ||
|
Pro Bodybuilder
Posts: 374 |
My body fat is in the 12-14 percent range, but there is no way that there is that much fat on my leg. I can hardly grab any fold if I pinch my quad. | ||
|
Amateur Bodybuilder
Posts: 64 |
Is one inch way to small for the glute? I am like 12-14% BF. | ||
|
Olympian 
Posts: 1959 |
DCS you know when you hit a bone. Needle size: max 25 gauge and 5/8 inch, no mather where i stick it. ------------------ Don't look back, life is too short | ||
|
Pro Bodybuilder
Posts: 487 |
I use 1 1/2 inch pins. I push at least half in. So 3/4 inch or more and no problems with absesses anywhere. I DO NOT use my glutes. They are big enough without site injecting them. I use quads, rear delts, and calfs. If those three are sore its bis and tris. |
All times are ET (US) | |
 |
|
|
posted April 13, 2001 01:58 AM