GEORGE SPELLWIN'S ANNOUNCEMENTS
Enlightening Men about Anabolic Steroids and Bodybuilding for over Two Decades
 UBBFriend: Email This Page to Someone! |
 George Spellwin's ELITE FITNESS Discussion Boards
 Anabolic Discussion Board
 how deep should pin go to hit muscle
|
| Author | Topic: how deep should pin go to hit muscle |
|
steeroid1 Amateur Bodybuilder (Total posts: 9) |
posted April 23, 2000 02:39 AM
  
when injecting how far should the pin go in 1 inch or more,have inch and a half pin,and where is the most direct spot? IP: Logged |
|
hardness Amateur Bodybuilder (Total posts: 94) |
posted April 23, 2000 02:41 AM
all the way in,glutes are the most comfy spot. again this ahs been answered before. IP: Logged |
|
Gobler Pro Bodybuilder (Total posts: 203) |
posted April 23, 2000 02:49 AM
Go in almost all the way at a slight angle. For some good info on injections check out 2thicks site IP: Logged |
|
steeroid1 Amateur Bodybuilder (Total posts: 9) |
posted April 23, 2000 02:51 AM
thanks,good to see people care out there. IP: Logged |
|
icron411 Amateur Bodybuilder (Total posts: 15) |
posted April 23, 2000 07:08 PM
bump IP: Logged |
|
flossin1 Amateur Bodybuilder (Total posts: 34) |
posted April 23, 2000 08:04 PM
1"should be adequate for the delt or quad should probaly use 1 1/2" for glute though. IP: Logged |
|
NEWMAXX Amateur Bodybuilder (Total posts: 41) |
posted April 23, 2000 08:20 PM
Not that I know anything..But ^^^^^ "quad" would be incorrect. Check out 2Thick's site: ------------------ IP: Logged |
|
Mojo Pro Bodybuilder (Total posts: 106) |
posted April 23, 2000 10:59 PM
How much fat do you have? That could also be a factor. From what i've learned I would go with a 23 gauge 1 1/2 in the glute. IP: Logged |
|
zarathustra Amateur Bodybuilder (Total posts: 25) |
posted April 25, 2000 09:08 AM
I've been injecting in my quad with a 23g x 1.5" and have had no problems at all. I think alot of problems happen when you dont go deep enough. Also the deeper the needle is the less it will move around. IP: Logged |
|
1 Amateur Bodybuilder (Total posts: 33) |
posted April 25, 2000 09:16 AM
depends on how fat u are. Pinch your injection site and divide by 2, thats your min. depth IP: Logged |
|
1 Amateur Bodybuilder (Total posts: 33) |
posted April 25, 2000 09:17 AM
i mean, thats where your muscle begins, so add another 1/2 inch at least IP: Logged |
|
Jeff_rys Amateur Bodybuilder (Total posts: 40) |
posted April 25, 2000 10:05 AM
I think one inch. I used 1 1/2 in the butt and hit a bone, no thanks. I am skinny so sometimes I use only 1/2 inch in the butt. You should inject rather high, if you go for the middle then you need a longer needle. Jeff IP: Logged |
|
Mr. T Pro Bodybuilder (Total posts: 404) |
posted April 25, 2000 01:00 PM
All the way in unless your skinny- IP: Logged |
All times are ET (US) | |
 |
|
|