Elite Fitness Bodybuilding, Anabolics, Diet, Life Extension, Wellness, Supplements, and Training Boards
Anabolic Discussion Board how long to shoot 2cc's thru a #25?
|
Author | Topic: how long to shoot 2cc's thru a #25? | ||
Amateur Bodybuilder Posts: 51 |
1 minute? 5 mins? 10 mins? half hour? 2 hours? 5 hours? all day? approx how long does it take u #25 guys? | ||
Amateur Bodybuilder Posts: 136 |
Depends on what you are shooting. I use 25g for all my gear and it takes some pressure but not too much time at all. Just gotta have strong kung fu fingers 1 cc might take around 30 seconds. | ||
Pro Bodybuilder Posts: 577 |
Winny, suspension......fast. Sus and others that are thicker can be a bitch, use a 22 or 23 ------------------ | ||
Elite Bodybuilder Posts: 949 |
what he said...nothing worse than 3cc's of omna in your left cheek being pushed through a 25g....23g and quads for me (or tri's ) | ||
Elite Bodybuilder Posts: 845 |
Just did a 1/2 cc of Sustanon in my right shoulder with a 25g needle, took about 1 minute. Not to bad, but OMFG does it hurt now! LOL | ||
Amateur Bodybuilder Posts: 257 |
sust is some thick shit, it takes me about a min to shoot 2 cc's ------------------ | ||
Elite Bodybuilder Posts: 949 |
pain is a 2cc mix of omna and phenyl prop in the tricep....swelling lasted 5 days..horseshoe finally came fully back in 10 days | ||
Amateur Bodybuilder Posts: 51 |
damn, I'm definately movin up to the #25 then. | ||
Elite Bodybuilder Posts: 666 |
The rule of thumb is that the injection should take as long as it took to draw. Thick oils injected too fast, or with too much pressure, accounts for a lot of the sore asses you hear about on the board. | ||
Amateur Bodybuilder Posts: 51 |
so the slower the better eh.. thx for the tip. when am i going to graduate out of this cool novice stuff... | ||
Elite Bodybuilder Posts: 666 |
Hey, man, nobody intelligent gives a shit about those "titles". There are lots of thoughtful guys like you that don't have a lot of posts on the board, and some idiots that have tons. But it's not hard to figure out who to listen to. | ||
Amateur Bodybuilder Posts: 51 |
hehe. I have noticed that. Was just messin around. sounds so corny, uknow.. Cool novice. makes me laugh. | ||
Pro Bodybuilder Posts: 343 |
Bro, If you are using the higher gauge pins like 23g or 25g it makes it easier if you hold the loaded syringe up to a light bulb for a minute before you inject. Heating the juice liquifies it and makes it easier to inject. LATE | ||
Amateur Bodybuilder Posts: 153 |
It seems like a few hours when you are doing it, but I have never timed it. | ||
Pro Bodybuilder Posts: 413 |
I am usually shooting 2cc through a 27g ping EOD. If before you inject you let it sit in a glass of warm water with the cap on of course. It really doesn't take that much time. With a 27g I usually do it in about 2-3 minutes. You do need a good grip because it does take some pressure to push it. I have foudn that BD pins have big finger slots that hold rather nicely. And no it is not the fact that I am scared of the larger pins. It is that on my 13th cycle shooting sometimes ED and EOD, you will tend to build up a lot of scar tissue, the smaller gauges tends to lesson the effect. Then you will get some that say use other muscle groups. Which is good for them, but I look at it this way. When you pierce the muscle and then inject a fluid into it. It builds up scar tissue. If you continue to inject in lets say your biceps, then you are breaking down muscle, and developing scar tissue there that will never grow again. My glute is not going to be worked that much so the scar tissue is not that big of a deal there. | ||
Elite Bodybuilder Posts: 1320 |
heat up the amp/vial by putting it in a glass of hot water for a few minutes. i use 25 guage for everything, takes about 20sec per cc......ya just gotta push hard....grrrr! | ||
Elite Bodybuilder Posts: 1215 |
Just took about 20 seconds. | ||
Amateur Bodybuilder Posts: 62 |
go with an 18 and it will be in you in no time. jk |
All times are ET (US) | |