posted March 23, 2000 08:27 PM            

---

Sorry for the lenght but this is a copy of the E-mail I sent Macrophage and I want to know what you guys have to sab=y thanks bros.

did my first shot today and lets just say I need your help! Used a 1 inch BD syringe for a quad shot. Scored it allright exept the top went flying but the trouble started when I went to draw it out. I put the needle in and pulled back but it wasn't coming all I got was some air and a drop or juice. So I took it and pulled out the pluger and poured it in but I slipped and spilled almost 1ML out of 2. Got the needle and stcuk it all the way in the outside quad muscle right in the middle of it about an inch above center. Went it almost TOO smooth I am actually worried I missed. Then went to aspirate, pulled back but the pluger wouldn't move so I assumed I was in a muscle and injected pretty slowly. When I pulled ou the needle some leaked out even though I stuck it in deep and used only 1ML! I now have some slight tingling in the area but no problem other than that as I can barely even find the spot where i injected. I really think I missed the muscle so I have a few things i need to ask since I only got like 90mg of test out of that shot

1) do you have any pictures of where to inject in the glute I really need this
2) how hard should it be to get the oil into the needle
3) how hard should it be to aspirate
4) how do I keep it from leaking
5) what is the easiest/proper way to draw from an amp

Any help would be apprectiated as I need to do anouther shot to make up and i dont have enough to mess up again

IP: Logged

posted March 23, 2000 08:33 PM         

---

Go to 2Thicks injection site .. hehehe
www.angelfire.com/biz5/syringes

IP: Logged

posted March 23, 2000 08:35 PM            

---

used his info btu he has nothing on quad shots

IP: Logged

posted March 23, 2000 08:36 PM         

---

Dude, check out any of 2thick's posts, he has a site showing where to inject. One more bit of advice I can give is be careful when you put the needle INTO the amp. I've made the mistake of tapping it off of the bottom and dulling the tip....HURT LIKE A BITCH!!! If you can, draw with one needle, inject with another. Good luck!

IP: Logged

posted March 23, 2000 08:36 PM         

---

It can be a little difficult to aspirate, but you don't need to pull back far... just so it barely moves. If you are in a vein it _should_ pull back quite easily. After you finish the injection swab the site with alcohol and put pressure on it for about 60 seconds. It might be easier for you to draw out of the amp if you heat it. Hold it under some very hot tap water for a little bit. Until it is warm.

Injecting into the glute. Divvide your ass cheek into quadrants, and inject into the upper outer quadrant. STAY AWAY FROM THE MIDDLE OF THE ASS. The middle is where the sciatic nerve is... you want to go on the upper part because in most asses, there is not as much muscle on the lower part, and there are more nerves there.

------------------
-------------------

the alpha male

IP: Logged

posted March 23, 2000 08:38 PM            

---

what gauge pins are you using
you should use 18,19, or 20 to draw and 22/23 to inject
and you should use inch and a half pins
it should not be hard to aspirate
sometimes the oil leaks out- too much pressure
dont worry about
just try to get it right next time
and check out the site mentioned in the above post

------------------
MP

IP: Logged

posted March 23, 2000 09:06 PM            

---

Injecting into the glute: Divide your ass cheek into quadrants, then divide the upper quadrant in four smaller quadrants and inject into the upper outer quadrant. Thats it!

IP: Logged

posted March 23, 2000 09:50 PM            

---

Thanks all but i do not have accsess to anything other than 23 gauge 1 inch and 1 1/2 inch pins and I have 25 of each so it kind of hard.

Will the pooring in method work if I am carefull?

IP: Logged

posted March 23, 2000 09:53 PM            

---

CB...head to the site. 2Thick sells needles and syringes.

------------------
If you racked the bar, then you're lifting the bar.

IP: Logged

posted March 23, 2000 09:55 PM            

---

got mine from him before I knew any better so all I got was 23 gauge and I am starting my cycle now

IP: Logged

All times are ET (US)