For an FAQ with Animal as well as variations of ways to make Finaplix injectable with the kit, click here.

1.) Here is the Sterile Kit as it surrounds a Fina cart.

Inventory is as follows:
1.) Vial with "Magic Solution"
2.) Vial with Oil
3.) Sterile Vial
4.) 0.45um GD/X Sterile Syringe Filter
5.) 10cc Syringe
6.) 5cc Syringe
7.) Fina Cart
8.) Two 18g Needles
9.) One Coffee Filter

3.) Cart sitting outside of it's sealed packaging.

4.) Add pellets to vial 1(magic vial).
Be sure not to dump the pellets everywhere when you remove the plastic top off the cart.
You can accelerate the breakdown of the pellets by crushing them. I did not.
You can also use heat to accelerate the breakdown. I did not.

5.). Let it set for less than 1 hour to prevent glue oxidation.
I purposely allowed it to set for a couple of days so it would oxidize, thus forcing me to pre-filter using the coffee filter (I did this so the documentation would be more thorough).
You do not want the glue to oxidize, unless you enjoy wasting time.

6.) Get out the 5cc syringe and attach one of the 18g needles. Draw 2cc's of oil out of vial 2 for purging the sterile filter at the very end of this process.

7.) Recap the 5cc syringe and store the 2cc's of oil for later use.

8.) Add the oil from vial 2 to vial 1 ever so gently (remember to do it within 1 hr).

9.) Pic of oil addition to vial 1 (again this should be done within 1 hr of adding pellets).

10.) At this point I gave it a gentle swirl and allowed it to settle. Your fina can sit at this state for over a years time and still be legit. The image below shows the recently swirled vial 1.

11.) By ensuring the oxidation of the glue (by not obeying the 1 hr rule). I was forced to pre-filter. This is where the coffee filter comes in handy. Insert a small funnel into vial 2 and insert the filter into the funnel as shown below in the pic. Don't pour yet, you must warm the mixture first.

12.) Warm the mixture up. Animal suggests warming in boiling water or on an electric eye. I used hot water from the sink faucet as shown below. This helped lower the viscosity of the mixture so it was easily poured.

13.) Pour the top layer into the funnel leaving the glues behind in vial 1.

14.) Allow the oil to drip through the filter and then pour the remaining oil/glue into the funnel and allow it to filter overnight. The next morning use rubber gloves( I used zip-loc bags over my hands) to protect your hands while wringing out the filter into the funnel.

15.) Preparation for using Version 4 ( or V4) of Animals Sterile filtering. You should have pre-filtered vial 2, sterile vial 3, sterile filter, 10cc syringe and two 18g needles. Attach one 18g needle to 10cc syringe. Remove cap from sterile vial 3 and insert the other 18g needle(you will feel the pressure equalize). You are now ready to draw and filter.

16.) Draw with the 10cc syringe.

17.) Replace the needle with the sterile filter. Insert filter into needle sticking out of sterile vial 3, and begin to filter.
As Animal warns, hold on to everything securely so your fina doesn't go flying.
Alternate instructions: Remove the needle, place the filter on the syringe, and then place the needle on the filter. Insert needle into stopper and filter the fina into the vial. NOTE: Leave the second needle in the stopper (the one used to release the pressure in the vial). By leaving the needle in the stopper this allows for the air inside the vial to remain at atmospheric pressure, thus when you release the plunger the air inside the vial will not be pressurized and try to back fill the syringe with what was liquid was left in the filter.

18.) Repeat the draw and filter above until all fina is sterile filtered into sterile vial 3. Then take the 5cc syringe (with the 2cc of oil you have stored) and purge the sterile filter of any remaining 'good' stuff as shown below.

19.) WHA-LA! There you have it. Time to go FEED YOUR CATTLE!