TNE test suspension homebrew

[smash1904]

Been registered and lurking here for awhile, great site. I usually post on AM but they don't have a place to discuss homebrewing, and I'm hoping I can get some help so heres my first post here:

Im doing my first homebrew and want to make sure I do it right. I have a good amount of tne and I'd like to make some some 100-200mg/ml with ethyl oleate.

Thanks.

 

[MaxxReps]

I thought test suspension was in water..

 

[smash1904]

I thought test suspension was in water..

I've seen how to make it with water and it seems simple enough... The thing is I want to learn how to homebrew with oil, and test suspension is what I have to work with. Also the recipes I've seen are for 50-100mg/ml and I hear its an extremely painful injection so I'm looking for an ethyl oleate blend to reduce pain at 100-200mg/ml. Finally I want a SOLUTION not a SUSPENSION - I want every dose to be exactly the same. I made liquid tbol before I started capping and it was a suspension which was really irritating.

 

[MaxxReps]

Just one of the hits from google

http://www.elitefitness.com/forum/b...ying-make-testosterone-suspension-720075.html

 

[smash1904]

Here's the recipe I'm currently looking at:

2% BA
20% BB
35% EO
the rest oil

or

3%BA
20%BB
the rest EO

I hear this makes 200mg/ml test prop painless...

Im using basskiller's calculator and homebrew directions. Will only heat to 250' and I want to use a whatman anotop 25 sterile filter 0.02um pore size - will this work or do I want a nylon filter or bigger pore size? How many ccs will one of these make before it clogs?

 

[smash1904]

Bump

 

[smash1904]

Just one of the hits from google

http://www.elitefitness.com/forum/b...ying-make-testosterone-suspension-720075.html

It eo is precisely what I need to use, not only to to reduce pain but also to get that higher concentration:

"You have to use EO oil, GS, CS or anything else will not hold unless you are 50mg/ml or less.."

Is a bb eo ba blend the best way to go or do I want just an eo ba blend? How often do people have reactions to eo?

 

[MaxxReps]

Hey wish I had answer for you but am interested in how you make out. Hope you will update this thread with your results.

 

[smash1904]

Alright thanks.

I will start by making 10cc of
2% BA
20% BB
35% EO
the rest oil
starting at 200mg/ml, then decreasing mg/ml by increasing volume making it 175mg/ml 150mg/ml 125mg/ml stopping at 100mg/ml or where it stops crashing first.

If that crashes I will make 10cc of
3%BA
20%BB
the rest EO
at 200mg/ml then same thing 175 150 125 100.

If that crashes I will make 10cc of
2-3% BA
the rest EO
at 200mg/ml then same thing 175 150 125 100.

1) How much BA?
2) What kind of filter? Should I filter through .45 .22 or both? Which brand, size, filter type?
3) Do I only need to heat to 250? Less? More?
I hear EO burns at a low temp, and destroys certain filter types.

 

[smash1904]

Ok so no more than 2% BA.

These might work as well:

2% BA
20% BB
39% EO
39% GSO

2% BA
49% EO
49% Oil

Will EO melt the rubber stopper and the rubber in the syringe?

 

[smash1904]

Also do I maybe want to use guaiacol?

 

[bmays]

If it is dissolved in oil it is not a suspension, it is a solution. No such thing as test suspension which is not water based.

 

[MaxxReps]

True but if there is no ester it should still be very quickly absorbed into the bloodstream, which is the goal of TNE. I don't know if it is possible (I'm pretty new to AAS) but if it were I'd prefer the solution to the suspension mainly for the fact that it is easier to consistently dose.

 

[Mh48500]

Seems like a lot of fuss over suspension, which IMO can add to a cycle but not really be the base. Either way since I am always the advocate of experimenting, let us know how it goes. Dont conform right?

 

[smash1904]

Heres what worked for me:

Test base 100mg/ml
BA 1%
BB 5%
G 16%
EO 48%
GSO 20%
This didn't hold so I bumped it up to 20% G and reheated. Held all the way down to 50' but will see if it falls out after a couple days.

 

[GoPower]

I totally disagree with using EO when making a TNE solution. The EO will hold it into the solution, it will also make it less available once injected. And for me, the whole purpose for using TNE is to have it immediately available right after the infection. The water based solutions are better for hormone availability, but are also painful.
A TNE/GSO/Guaiacol is freakin' amazing! It takes less than a half hour to be fully active and clears your system in a day. And the best part about it Is that it is completely painless.