homebrew test is killing me

[rob2534]

Guys, how can I fix this without discarding the remaining gear. Bought some homebrew test 350 enan/prop mix from a buddy of mine who is a national level competitor. The stuff leaves severe pain and lumps 2 days after every injection. I've got 50 cc's and have battled thru 30 of that with this past cycle. Before I use the rest in the future, any ideas how to bring down the potency or could this stuff be bunk or just wayyy too strong? I didn't wanna insult him so I figured I'd come here. Thanks!

 

[simply dave]

Guys, how can I fix this without discarding the remaining gear. Bought some homebrew test 350 enan/prop mix from a buddy of mine who is a national level competitor. The stuff leaves severe pain and lumps 2 days after every injection. I've got 50 cc's and have battled thru 30 of that with this past cycle. Before I use the rest in the future, any ideas how to bring down the potency or could this stuff be bunk or just wayyy too strong? I didn't wanna insult him so I figured I'd come here. Thanks!

I brew my own gear, both enanthate and propionate. The Test E is always "smooth". The Test P on the other hand hurts like hell. I'm not sure there is any way around it but some others may have some solution(s)/suggestions.

 

[Judo Tom]

get some test e and dilute it with that

 

[jmat2407]

get some test e and dilute it with that

Thats retarded. Most other test vials are going to be 250 mg/ml it would take a good amount of it to significantly reduce the concentration of that 350 to under 300. No instead what you simply do is...

Guys, how can I fix this without discarding the remaining gear. Bought some homebrew test 350 enan/prop mix from a buddy of mine who is a national level competitor. The stuff leaves severe pain and lumps 2 days after every injection. I've got 50 cc's and have battled thru 30 of that with this past cycle. Before I use the rest in the future, any ideas how to bring down the potency or could this stuff be bunk or just wayyy too strong? I didn't wanna insult him so I figured I'd come here. Thanks!

Cut it with sterile oil till you bring the concentration down to around 250mg/ml. Add more solvents if need be depending on original recipe.

Sounds like your source needs to work on his recipe my 300mg test is painless I usually make with a 2/18 ration of BA and BB.

 

[ppgfreak]

I buy home brew sust 300 or test E 250 and its smooth. The prop is always painful, regardless where I got it.

Sent from my ADR6350 using EliteFitness

 

[Mh48500]

I agree with cutting it with the oil, but I would say do not add more solvent. Unless the hormone is crashing what would be the point of adding more of an irritating substance? It is more likely that the percentage of BB is causing the soreness and irritation than anything. Test e at 250mg/ml will hold with zero BB, teat prop at 100mg/ml will hold fine at 3% BB, what would be the point of using 18%? Put some BB on your fingers then touch your lips, that stuff is extremely irritating to the skin. When you draw up BA with a syringe if it leaks onto the syringe the painted numbers literally rub off.

Solvents are extremely irritating the body and simply are not necessary in high amounts to suspend most hormones.

Cut it with oil, filter and give it a go.

Good luck!

 

[rob2534]

I only wish I were as smart as u mad scientists, lol. I am clueless on homebrewing, much less cutting it to bring down the potency. Hmmmmm, what to do, what to do.

 

[rob2534]

I ran straight prop 200mg/ml last contest season and had NO pain from it. It won me the overall cause I looked damn good. I've never done prop that is painful until now, if that's what it even is.

 

[Judo Tom]

thanks for calling me retarded... its always nice to hear

trust me.. take a vial of prop and a vial of test cyp

inject the prop once. if it burns next time just mix the prop and the cyp in the same syringe and tell me about the difference in pain.

so im suggesting get two vials of test cyp, say 200-250mg, mix that with the vial of the prop/cyp mix

now you will have 1 vial of test 'cyp' that is basically 250mg or close and im willing to be that the pain will be minimal.

most likely the pain is from the BA not the test.

if you mix in 2-3 parts oil.. now what.. start shooting 3ml just to get 300mg of test.. no thanks..

 

[25homes]

Cut with sterile oil or odds are it is painful from high BA contenf. Which you could put in oven for 10 min at 225 degree with pin in top and some of that BA will evap off which will help tremendously