CloudyTest E. 300mg/ml

[teenwulf]

hey guys,
i just opened a bottle of test E, its 300mg/ml and is in a 20 cc bottle. i have had it for a few weeks and just now opened it. its from a very reliable source and have used his gear many times in the past with no problems. however, when i opened this box the test is very cloudy, and i have no idea what to do? is it ok to just inject it, or how can it get it to clear up?

thanks for the help guys

 

[Mr.X]

It probably crashed, heat it up. You can use my baking instructions to do it, or just put it in warm/hot water. (don't boil)

 

[teenwulf]

i tried putting it in hot water for about one minute, it cleared for about thirty seconds and then went back to cloudy, anybody ever have this happen to them? what happens if you just shoot it like this? also, Mr. X where are your baking instructions?

thanks

 

[black sheep]

Preheat the oven to 250 degrees. Put a pin in the stopper and put it in the 250 degree oven for 10 minutes. Remove it while hot, shake it up and let it cool naturally. That should do the trick. I had the same problem with test awhile back, and that did the trick.

 

[teenwulf]

is the gear safe to use? a friend of mine said that it still ok to use and the sterilty and the the dosing wouldnt be affected at all!!!
any thoughts on this

thanks guys

 

[teenwulf]

bump, anybody?

 

[NYC]

Test E will NOT crash at 300mg/ml. Test enan is oil soluble, solvents arent even necessary. If it is getting cloudy, it is probably another hormone that was used....

 

[teenwulf]

ok i emailed my source and he says it will be fine and that some moisture probablly just got into since it was so cold when it was shipped. he says that the sterity and the dosing are fine and that it is safe to inject? nyc, why is it impossible for this to crash? anybody else have any thouhgts on this?

thanks for all the help!!

 

[NYC]

Because test enanthate is oil soluble..It doesnt even require ba or bb to stay in solution. Once it is in solution it stays there, even at 500+mg/ml. Ive been brewing for years and know this for a fact.

 

[teenwulf]

anybody else? i really trust this source, byt if nyc knows this for a fact im not sure what to do, nobody has ever had test e do this? i googled this and some information came up about test e that is cloudy. NOTE: Use of a wet needle or wet syringe may cause the solution to become cloudy; however this does not affect the potency of the material, or the sterility. this was from

PDR Drug information for
TESTOSTERONE ENANTHATE
Manufacturer: Savient

so if its impossible for test e to get cloudy why would it say this on the drug information pamphlet?? i know it hasnt had a wet needle in it, but it could have very easily have gotten moisture in it due to the cold weather conditions that it was shipped in.

anybody else have any opinions? nobody else has had this happen?

thanks guys

 

[teenwulf]

bump
anybody else?

 

[black sheep]

bump
anybody else?

DO what I told you...

 

[used2juice]

Because test enanthate is oil soluble..It doesnt even require ba or bb to stay in solution. Once it is in solution it stays there, even at 500+mg/ml. Ive been brewing for years and know this for a fact.

NYC is correct. Test enanthate may not be properly suspended, but it can't get "cloudy." You likely have test cypionate, which can easily crash if the weather gets a little cold.

 

[teenwulf]

then how come on the website for Savient Test enanthate it talks about how it can get cloudy if perspiration gets into the vial? i am not saying you guys are wrong, i am just trying to understand all of this! also, lets say it is cypionate, is it ok to shoot it while cloudy? blacksheep, does it matter what needle size you need? and i assume the tip of the needle should not be in the liquid?

sorry for all the questions guys, this has just never happened to me!
has anybody innjected test that looks like this?

 

[black sheep]

then how come on the website for Savient Test enanthate it talks about how it can get cloudy if perspiration gets into the vial? i am not saying you guys are wrong, i am just trying to understand all of this! also, lets say it is cypionate, is it ok to shoot it while cloudy? blacksheep, does it matter what needle size you need? and i assume the tip of the needle should not be in the liquid?

sorry for all the questions guys, this has just never happened to me!
has anybody innjected test that looks like this?

Anything with a lower number than 25, 23 or 22ga is good. No, keep the tip up in the open space above the gear. Stop stressing already... Try what I told you.. You're gear is fine

 

[used2juice]

then how come on the website for Savient Test enanthate it talks about how it can get cloudy if perspiration gets into the vial? i am not saying you guys are wrong, i am just trying to understand all of this! also, lets say it is cypionate, is it ok to shoot it while cloudy? blacksheep, does it matter what needle size you need? and i assume the tip of the needle should not be in the liquid?

sorry for all the questions guys, this has just never happened to me!
has anybody innjected test that looks like this?

My bad, I was assuming the vial was sealed well enough that no perspiration got in there. My worry now would be if water was able to find its way in to that vial, what else has?

 

[immortalis]

Preheat the oven to 250 degrees. Put a pin in the stopper and put it in the 250 degree oven for 10 minutes. Remove it while hot, shake it up and let it cool naturally.

This is exactly what you should do.